IN DEVELOPMENT / MATRIX SERIES
MATRIX ELITE P7020
The next flagship of the MATRIX series.
75%Solids content
NANOLAB®PPF, VINYL & PAINT
CHEMISTRY YOU CAN TRUST.50 ml
PPF, VINYL & PAINT
MATTE. Ceramic coating for matte finishes
Protection that respects the finish.
A single-layer ceramic coating designed for matte clear coat, paint protection film and vinyl, with a slick, hydrophobic surface.
Designed for
Matte clear coat, matte PPF and matte vinyl wraps
50 mlApplication guidance below
1Coating layer
50 mlBottle size
30 minTack-free time
Developed for the surface.
Designed for the process.
Made for matte.
Protect the surface while preserving the intended satin appearance.
Slick and hydrophobic.
Bring ceramic coating benefits to compatible matte paint and films.
Consistency matters.
A systematic application across each complete part helps maintain uniform coverage.
02 / KNOW YOUR FORMULAThe details
The details
make the difference.
Choose the right product for your surface. Follow the current application and care guidance.
- Product
- MATTE
- Category
- Ceramic coating for matte finishes
- Size
- 50 ml
- Compatible surfaces
- Matte clear coat, matte PPF and matte vinyl wraps
Application level3/10
1 = Easiest · 10 = More technique
A straightforward process with attention to preparation, even coverage and the recommended timing.
Lower scores mean easier application. Higher scores reflect more technique and familiarity with the process. With experience, even a 10/10 product can feel straightforward.
Apply methodically across a complete part for even coverage. Follow the product-specific buffing instructions for matte surfaces.
03 / APPLICATION & CAREA considered process.
A considered process.
A lasting impression.
Read the full instructions before you begin.
How To Apply
Pre-Application Preparation: Ensure a clean surface by thoroughly removing any traces of oil, grease, fat, fingerprints, etc., using our recommended PREP solution.
Tools Required: In addition to the coating material, prepare an applicator pad and a microfiber towel.
Application Method:
Apply an adequate amount of the coating material onto the applicator pad, ensuring it’s sufficiently primed for even distribution. If the applicator feels “stuck”, apply more material as needed.
Achieving optimal results when applying a matte surface coating lies in the methodical approach. Employing a systematic technique, such as applying a full part, such as a hood, door ect., ensures a uniform coverage.
Buffing Phase: To promote strong adhesion, refrain from wiping the coating immediately post-application. allow the coating to sit until “sweat” marks appear. This indicates that the coating has fully cross-linked with the surface. Use the microfiber towel to swiftly remove excess material in straight lines; Subsequently, flip the microfiber towel to buff the surface, ensuring no high spots remain.
Curing Times:
Tack-Free: 30 minutes
Initial Curing: 12/24 hours (weather-dependent)
First Wash: 14 days
Full Curing: 30 days
Storage
NANOLAB MATTE. has a shelf life of at least 12 months when stored between 0°C / 32°F and 25°C / 77°F in the tightly closed original container.
After opening – must be used within 180 days.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable.
In this case however, the properties required for the intended use must be checked for quality assurance reasons.
Maintenance
MATTE offers a one-year warranty, ensuring lasting protection for your surfaces.
DO NOT POLISH A MATTE SURFACE!
To maintain the validity of the warranty, it’s crucial to follow these maintenance steps every 6 months by a NANOLAB Certified Installer:
- Wash: Begin by thoroughly washing the coated surface using a pH-neutral car shampoo and a microfiber wash mitt. Rinse off any dirt and debris.
- Drying: After washing, dry the surface using a clean microfiber drying towel or a forced-air blower. Avoid air-drying to prevent water spots.
- Inspection: Carefully inspect the coating for any signs of damage, such as areas where the coating may have worn off. Address any issues promptly.
- Ceramic Coating Re-Application: Apply another MATTE ceramic coating layer to enhance the hydrophobic properties of the coating and boost its longevity. Follow product’s instructions for application.
Throughout the one-year period, it’s essential to avoid using abrasive cleaners or harsh chemicals that could degrade the ceramic coating. Regular maintenance and timely repairs will help maximize the durability and performance of the coating over time.
Material Safety Data Sheet
COMPLETE THE PROCESS
All products ↗Find your next step.
YOUR NEXT GREAT FINISH STARTS HERE
Make it MATTE.
Connect with a distributor for availability and product support.