IN DEVELOPMENT / MATRIX SERIES
MATRIX ELITE P7020
The next flagship of the MATRIX series.
75%Solids content
NANOLAB®GLASS PROTECTION
CHEMISTRY YOU CAN TRUST.50 ml
GLASS PROTECTION
WINDOWS. Hydrophobic ceramic glass coating
Let the water move on.
A ceramic coating for exterior glass, designed to make water bead and roll off while protecting the surface against environmental contamination.
Designed for
Exterior automotive glass surfaces
50 mlApplication guidance below
50 mlBottle size
30 minTack-free time
30 daysFull cure
Developed for the surface.
Designed for the process.
Hydrophobic glass.
Designed to encourage water beading and runoff.
A prepared surface matters.
Remove oils and residues before applying for consistent contact with the glass.
Maintain the effect.
Clean thoroughly and reapply as described in the maintenance guidance.
02 / KNOW YOUR FORMULAThe details
The details
make the difference.
Choose the right product for your surface. Follow the current application and care guidance.
- Product
- WINDOWS
- Category
- Hydrophobic ceramic glass coating
- Size
- 50 ml
- Compatible surfaces
- Exterior automotive glass surfaces
Application level3/10
1 = Easiest · 10 = More technique
A straightforward process with attention to preparation, even coverage and the recommended timing.
Lower scores mean easier application. Higher scores reflect more technique and familiarity with the process. With experience, even a 10/10 product can feel straightforward.
Before application, avoid cleaners containing silicones or waxes, including some anti-fingerprint formulations.
03 / APPLICATION & CAREA considered process.
A considered process.
A lasting impression.
Read the full instructions before you begin.
How To Apply
Pre-Application Preparation: Ensure a crystal clear surface by thoroughly removing any traces of oil, grease, fat, fingerprints, etc., using our recommended PREP solution.
Tools Required: In addition to the coating material, prepare an applicator pad and two microfiber towels. Opt for towels of different colors if possible for better organization.
Application Method:
Apply an adequate amount of the coating material onto the applicator pad, ensuring it’s sufficiently primed for even distribution. If the applicator feels “stuck”, apply more material as needed.
Commence by outlining the area for application, starting from the surface edges. Then, create a central X shape to facilitate uniform coverage.
Employ crisscross motions to spread the material along the X and Y axes, ensuring thorough coverage.
For optimal results, consider applying an additional layer while the previous one is still “liquid” to guarantee complete coverage.
Buffing Phase: To promote strong adhesion, refrain from wiping the coating immediately post-application. Allow it to haze over or display the rainbow effect before proceeding. Use the first towel to swiftly remove excess material in straight lines; speed is key at this stage, with no need for perfection. Subsequently, utilize the second towel to buff the surface in circular motions, ensuring no high spots remain.
Curing Times:
Tack-Free: 30 minutes
Initial Curing: 12/24 hours (weather-dependent)
First Wash: 14 days
Full Curing: 30 days
Storage
NANOLAB WINDOWS. has a shelf life of at least 12 months when stored between 0°C / 32°F and 25°C / 77°F in the tightly closed original container.
After opening – must be used within 180 days.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable.
In this case however, the properties required for the intended use must be checked for quality assurance reasons.
Maintenance
When preparing for maintenance, ensure thorough surface cleaning using PREP / APC to eliminate any potential barriers that might lead to application failures.
Apply an additional layer and get ready to enjoy a seamless experience.
Remember to avoid using any cleaners containing silicones / waxes prior to application, these are often present in anti-fingerprint formulations and may cause coating failure / clogging.
Material Safety Data Sheet
COMPLETE THE PROCESS
All products ↗Find your next step.
YOUR NEXT GREAT FINISH STARTS HERE
Make it WINDOWS.
Connect with a distributor for availability and product support.